Author Topic: Unlock Your Datasette  (Read 75951 times)

Offline cbmx

  • Newbie
  • *
  • Posts: 3
    • View Profile
Re: Unlock Your Datasette
« Reply #15 on: May 21, 2020, 11:40:22 PM »
merhaba
bu resimdeki bord resmini netten buldum. Bendeki bordun aynısı, yükle işlemini başarılı bir şekilde yaptım, fakat kasede kayıt yapmak için hangi pinlere lehim yapmam gerekiyor bulamadım.

Offline Remzi

  • Administrator
  • Full Member
  • *****
  • Posts: 106
    • View Profile
Re: Unlock Your Datasette
« Reply #16 on: May 22, 2020, 09:30:35 AM »
Merhaba,hosgeldiniz.
Elimde bu board'dan var.Pazar gunu kasete kayit yapmayi deneyip sonuclari burada paylasirim.

Offline cbmx

  • Newbie
  • *
  • Posts: 3
    • View Profile
Re: Unlock Your Datasette
« Reply #17 on: May 22, 2020, 07:38:21 PM »
hoşbuldum
teşekkür ederim

Offline Remzi

  • Administrator
  • Full Member
  • *****
  • Posts: 106
    • View Profile
Re: Unlock Your Datasette
« Reply #18 on: May 24, 2020, 08:08:04 PM »





Direnc veya kondansator kullanmadan,direk isaretli pinlere baglanti yapabilirsin.

Buradaki oyunlardan Commando'yu kaydedip denedim,sorunsuz calisti.

Kayit yaparken sesini sonuna kadar ac.Kasetten C64'e yuklerken,kayit yaparken kullandigin ses kaynagini kapatmayi unutma.
« Last Edit: May 24, 2020, 08:10:02 PM by Remzi »

Offline cbmx

  • Newbie
  • *
  • Posts: 3
    • View Profile
Re: Unlock Your Datasette
« Reply #19 on: May 24, 2020, 09:03:19 PM »
hemen deneyeceğim, bilgi için teşekkürler  :)

Offline Wakd21

  • Newbie
  • *
  • Posts: 1
    • View Profile
Re: Unlock Your Datasette
« Reply #20 on: September 29, 2020, 02:36:12 AM »
I have a Mode 1530 board and I cannot see where to solder the wire for ground and left.




Offline Remzi

  • Administrator
  • Full Member
  • *****
  • Posts: 106
    • View Profile
Re: Unlock Your Datasette
« Reply #21 on: September 30, 2020, 05:36:58 PM »
I marked the LEFT and GND on the photo below.
You need to use a 100nf capacitor or a 100K resistor.

>
« Last Edit: November 21, 2021, 03:34:37 PM by Remzi »

Offline backtogeek

  • Newbie
  • *
  • Posts: 8
    • View Profile
Re: Unlock Your Datasette
« Reply #22 on: December 14, 2020, 10:57:05 AM »
Thanks from the future :)

I was looking for a similar board to mine after finding another guide and found this one, is a 100kohm resistor required on the left for this as other guides have suggested?
« Last Edit: November 21, 2021, 03:34:54 PM by Remzi »

Offline backtogeek

  • Newbie
  • *
  • Posts: 8
    • View Profile
Re: Unlock Your Datasette
« Reply #23 on: December 14, 2020, 11:32:44 AM »
actually, I re-read everything and found more info in this post too.

I did not have any ceramic caps so I put a 0.1uF electrolytic capacitor on instead, positive side soldered to the board.

This time it came up saying "found file"

However it did not ultimately load even the intro screen, i will experiment a bit further and update for other future people.

Offline backtogeek

  • Newbie
  • *
  • Posts: 8
    • View Profile
Re: Unlock Your Datasette
« Reply #24 on: December 14, 2020, 01:53:18 PM »
Ok all working:




Little youtube video pre-cable tidy:


I hope that perhaps helps someone in the future.

Offline Remzi

  • Administrator
  • Full Member
  • *****
  • Posts: 106
    • View Profile
Re: Unlock Your Datasette
« Reply #25 on: December 14, 2020, 03:31:30 PM »
That's a grand job mate  ;)
Thanks for posting your results.

Offline backtogeek

  • Newbie
  • *
  • Posts: 8
    • View Profile
Re: Unlock Your Datasette
« Reply #26 on: December 14, 2020, 04:38:25 PM »
That's a grand job mate  ;)
Thanks for posting your results.

Thanks, I don't suppose you are aware of anything like tapdancer or CDT2WAV (Amstrad cpc464 equivalent mod) that runs on PC/Windows (or linux) ?

It would save a lot of effort and steps if I did not need to convert every single game to wav first.

Offline backtogeek

  • Newbie
  • *
  • Posts: 8
    • View Profile
Re: Unlock Your Datasette
« Reply #27 on: December 14, 2020, 07:00:40 PM »
I just got another old one out of my junk box, the heads are gone on this one, it shows absolutely nothing when running any tape head alignment so I might as well do the same to this one as it will never read tapes again.

I cant seem to identify the left on it though, any ideas?


Offline backtogeek

  • Newbie
  • *
  • Posts: 8
    • View Profile
Re: Unlock Your Datasette
« Reply #28 on: December 16, 2020, 09:47:10 PM »
Sorry for the bump, anyone got any ideas on the board above before I buy an oscilloscope :)

Offline Remzi

  • Administrator
  • Full Member
  • *****
  • Posts: 106
    • View Profile
Re: Unlock Your Datasette
« Reply #29 on: December 17, 2020, 08:10:21 AM »
I need to check my tape decks to find one with the same board.